Footbot/Real robot information

From IridiaWiki
(Difference between revisions)
Jump to: navigation, search
(Battery)
 
(38 intermediate revisions by 4 users not shown)
Line 1: Line 1:
= EPFL LSRO Wikipages =
+
This page does not exist anymore. Please go to:
   
For updated info go to the EPFL wiki.
+
http://iridia-dev.ulb.ac.be/projects/argos/trac/wiki/WikiStart#RealRobotInformation
http://wiki.epfl.ch/mobots-robots
 
 
= Connecting to a footbot =
 
 
Wifi uses wpasupplicant to connect to a WPA-PSK access point. You can use USB or Bluetooth to connect to the robot otherwise. Set the selector on the robot top to an even value for USB, and uneven to Bluetooth.
 
 
== USB ==
 
 
$ sudo /sbin/ifconfig usb0 192.168.0.200 netmask 255.255.255.0
 
$ ssh root@footbot_usb
 
 
footbot_usb is aliased to ip 192.168.0.202 in /etc/hosts.
 
In asebastudio, to connect use
 
tcp:host=192.168.0.202;port=33333
 
 
== Bluetooth ==
 
 
TODO: configuration of udev for bluetooth access
 
 
In asebastudio, to connect use
 
ser:device=/dev/footbotXX
 
 
== Wifi ==
 
 
Currently unstable, check LSRO wiki.
 
 
= Booting Algorithm =
 
 
Beware of the sudden movement of the robot as it's booting. NEVER put it on a table when testing.
 
If Aseba connection doesn't work, try again without killing asebamedulla; otherwise, close Asebastudio, kill asebamedulla and reset the traslator and the pic. Rerun asebamedulla and try connecting.
 
The command to run asebamedulla is the following:
 
 
$ asebamedulla --system "ser:device=/dev/ttymxc4;fc=hard;baud=921600" 2>&1 1>/dev/null &
 
 
If this does not work, try closing Asebastudio, killing asebamedulla and setting the selector to another even value (NOT an odd one!). Reset the pic and the translator, rerun asebamedulla and try
 
connecting again.
 
 
= Battery =
 
 
* full battery = 4.2V
 
* empty battery < 3.6V
 
 
The charger we have at Iridia damages the batteries.
 
We were given 12 batteries; to limit the number of damaged batteries, 10 batteries, when empty, won't be recharged.
 
Only two batteries will be recharged.
 
 
= Sensors =
 
 
== Camera ==
 
 
Cameras don't work at the same time; you can use them one by one.
 
To select the camera to use, echo to file /sys/class/gpio/gpio28/value
 
a value of 0 for the omnidirectional camera and 1 for the front one.
 
 
The camera module is mt9t031.ko.
 
 
If you get an error such as:
 
 
[FATAL] Cannot open /dev/video0: Input/output error
 
 
then try unbinding the driver and then binding it back. You do it this way:
 
 
echo 0-0 > /sys/bus/soc-camera/drivers/camera/unbind
 
echo 0-0 > /sys/bus/soc-camera/drivers/camera/bind
 
 
For problems, the EPFL guy to ask is Valentin Longchamps <valentin.longchamps@epfl.ch>.
 
 
= Actuators =
 
 
== Turret Rotation ==
 
 
At boot, the robot sets the 0 position of the turret. To avoid damaging the robot or having funny values, always put the gripper back in the 0 position and then switch the robot on. It can be done also when the robot is on already: set the variable 'rev.pid.enable' to 0 and rotate the turret back to its position. Then select 'Tools->Reboot->Griper-led' and the new 0 position will be set.
 
 
= Framework =
 
 
== Compiling ARGoS for the real robot ==
 
 
Download and install the toolchain from http://wiki.epfl.ch/mobots-robots/toolchain . It is recommended to install it system-wide because it hasn't been tested otherwise.
 
 
Configure your environment for cross-compilation:
 
 
$ source /usr/local/angstrom/arm/environment-setup
 
 
Then, compile the common package:
 
 
$ cd /path/to/argos2
 
$ cd common
 
$ mkdir -p build/footbot
 
$ cd build/footbot
 
$ cmake -DARGOS_COMPILE_REAL_FOOTBOT=1 ../..
 
$ make
 
 
If everything goes OK, compile the real robot package:
 
 
$ cd /path/to/argos2
 
$ cd real_robot
 
$ mkdir -p build/swarmanoid/footbot
 
$ cd build/swarmanoid/footbot
 
$ cmake ../../../swarmanoid/footbot
 
$ make
 
 
If everything goes OK, compile the user package:
 
 
$ cd /path/to/argos2
 
$ cd user/my_user
 
$ mkdir -p build/footbot
 
$ cd build/footbot
 
$ cmake -DARGOS_COMPILE_REAL_FOOTBOT=1 ../..
 
$ make
 
 
== Installing the libraries in the real robot ==
 
 
If you log into the robot, you'll notice a directory ARGoS. It contains the aseba backend (aseba_backend.aesl), some useful tools in bin/ and
 
a directory lib/ in which the ARGoS libraries are stored. Whenever you fix the common or real robot packages, you have to update these libraries. To
 
do it, the handiest way is the following.
 
 
Create a directory to install ARGoS locally:
 
 
$ cd /path/to/argos2
 
$ mkdir install
 
 
Install the common package libraries:
 
 
$ cd common/build/footbot
 
$ DESTDIR=../../../install make install
 
 
Same thing for the real robot package:
 
 
$ cd /path/to/argos2
 
$ cd real_robot/build/swarmanoid/footbot
 
$ DESTDIR=../../../../install make install
 
 
Now go into the install directory:
 
 
$ cd /path/to/argos2
 
$ cd install
 
 
And get into the directory where the libraries have been copied:
 
 
$ cd usr/local/lib/argos2
 
$ ls
 
 
Copy all the libraries onto the robot:
 
 
$ scp * root@footbot_usb:~/ARGoS/lib/
 

Latest revision as of 10:57, 20 April 2010

This page does not exist anymore. Please go to:

http://iridia-dev.ulb.ac.be/projects/argos/trac/wiki/WikiStart#RealRobotInformation

Personal tools